Search Results

A new technique for combustion diagnostics of a spark ignition engine was developed. In this method the ion sensor with the circular configuration was installed into the cylinder head gasket. This sensor is expected to be applied for production engine. The signal measured by the ion sensor was similar with that of cylinder pressure. The peak timing of ion current was consistent with the peak timing of pressure. There was a strong correlation between IMEP and the peak timing of ion current. This sensor is available to detect combustion quality in a spark ignition engine.

A chemical kinetics and computational fluid-dynamics (CFD) analysis was performed to evaluate the combustion of syngas derived from biomass and coke-oven solid feedstock in a micro-pilot ignited supercharged dual-fuel engine under lean conditions. For this analysis, a reduced syngas chemical kinetics mechanism was constructed and validated by comparing the ignition delay and laminar flame speed data with those obtained from experiments and other detail chemical kinetics mechanisms available in the literature. The reaction sensitivity analysis was conducted for ignition delay at elevated pressures in order to identify important chemical reactions that govern the combustion process. We have confirmed the statements of other authors that HO2+OH=H2O+O2, H2O2+M=OH+OH+M and H2O2+H=H2+HO2 reactions showed very high sensitivity during high-pressure ignition delay times and had considerable uncertainty.

The objective of this study is to investigate the performance and emissions in a pilot-ignited supercharged dual-fuel engine, fueled with different types of gaseous fuels under various equivalence ratios. It is found that if certain operating conditions are maintained, conventional dual-fuel engine combustion mode can be transformed to the combustion mode with the two-stage heat release. This mode of combustion was called the PREMIER (PREmixed Mixture Ignition in the End-gas Region) combustion. During PREMIER combustion, initially, the combustion progresses as the premixed flame propagation and then, due to the mixture autoignition in the end-gas region, ahead of the propagating flame front, the transition occurs with the rapid increase in the heat release rate.

Effects of injection parameters on combustion and emission characteristics of diesel PCCI engine operating on optical and test engine was investigated. PCCI combustion was achieved through slightly narrow included angle injector, low compression ratio coupled with exhaust gas recirculation. Analysis based on diesel spray evolution, combustion process visualization and analysis was carried out. Spray penetration was evaluated and related to the exhaust emissions. Advancing the injection timing and EGR extended the ignition delay, decreased NOx emissions and increased HC, smoke and CO emissions. Higher injection pressure led to low emissions of NOx, smoke, HC and comparable CO. Optimum spray targeting position for minimum emission was identified. Impingement on the piston surface led to deterioration of emissions and increased fuel consumption while spray targeting the upper edge of Derby hat wall showed improvement in emission and engine performance.

The present study helps to understand the local combustion characteristics of PREmixed Mixture Ignition in the End-gas Region (PREMIER) combustion mode while using increasing amount of natural gas as a diesel substitute in conventional CI engine. In order to reduce NOx emission and diesel fuel consumption micro-pilot diesel injection in premixed natural gas-air mixture is a promising technique. New strategy has been employed to simulate dual fuel combustion which uses well established combustion models. Main focus of the simulation is at detection of an end gas ignition, and creating an unified modeling approach for dual fuel combustion. In this study G-equation flame propagation model is used with detailed chemistry in order to detect end-gas ignition in overall low temperature combustion. This combustion simulation model is validated using comparison with experimental data for dual fuel engine.

Hydrogen spark-ignition (SI) engines based on direct-injection (DI) have been investigated because of their potential for high thermal efficiency and solving the problems related to knocking, backfiring, and pre-ignition. Wide range flammability limits in hydrogen engine enable smooth engine operation for a very lean mixture with low NOX. However, a too lean mixture may increase ignition delay and causes severe cyclic variations. There is a possibility that the turbulence occurred during injection of fuel surround the spark plug in the combustion chamber is major contributor to this phenomenon. To overcome this problem, a better understanding of the spark discharge and spark ignition during transient hydrogen jet is necessary. Therefore, it is very important to study an effect of local equivalence ratio and behavior of spark discharge in SI engine. This paper describes a mixing process of hydrogen jet using spark-induced breakdown spectroscopy (SIBS) in a constant volume vessel.

This paper describes the development and application of a spark plug sensor using a 3.392 μm infrared absorption technique to quantify the instantaneous gasoline concentration near the spark plug. We developed an in situ laser infrared absorption method using a spark plug sensor and a 3.392 μm He-Ne laser as the light source; this wavelength coincides with the absorption line of hydrocarbons. First, we established a database of the molar absorption coefficients of premium gasoline at different pressures and temperatures, and determined that the coefficient decreased with increasing pressure above atmospheric pressure. We then demonstrated a procedure for measuring the gasoline concentration accurately using the infrared absorption technique. The history of the molar absorption coefficient of premium gasoline during the experiment was obtained from the established database using measured in-cylinder pressures and temperatures estimated by taking the residual gas into consideration.

A small Cassegrain optics sensor was developed to measure local chemiluminescence spectra and the local chemiluminescence intensities of OH*, CH*, and C2* in a four-stroke spark-ignition (SI) engine in order to investigate the propagation characteristics of the turbulent premixed flame. The small Cassegrain optics sensor was an M5 type that could be installed in place of a pressure transducer. The measurements could be used to estimate the flame propagation speed, burning zone thickness, and local air/fuel (A/F) ratio for each cycle. The specifications of the small Cassegrain optics sensor were the same as those used for previous engine measurements. In this paper, measurements were made of several A/F ratios using gasoline to fuel the model engine. The performances of two Cassegrain optics sensors were compared to demonstrate the advantages of the new small sensor by measuring the local chemiluminescence intensities of a turbulent premixed flame in the model engine.

A heterodyne interferometry system with a fiber-optic sensor was developed to measure the temperature history of unburned gas in a spark-ignition engine. A polarization-preserving fiber and metal mirror were used as the fiber-optic sensor to deliver the test beam to and from the measurement region. This fiber-optic sensor can be assembled in an engine cylinder head without a lot of improvements of an actual engine. Adjustment system in the sensor was revised to face the distributed index lens with metal mirror. Before the flame arrived at the developed fiber-optic sensor, measured temperature was almost same with the temperature history after the spark, assuming that the process that changes the unburned gas is adiabatic. In situ unburned gas temperature measurements before knocking in a commercially produced SI engine can be carried out using developed fiber-optic heterodyne interferometry system.

The purpose of this study was to characterize the air/fuel ratio (AFR) of turbulent premixed flames in a spark-ignition (SI) engine. We developed a spark plug sensor with an optical fiber to detect the chemiluminescence spectra, specifically the intensity of the spectral lines related to OH*, CH*, and C2* free radicals. The sensor was composed of a sapphire window and optical fiber and is applicable to automobile SI engines. Measurements of the chemiluminescence intensity from OH*, CH*, and C2* radicals were obtained in turbulent premixed flames with a propane-air mixture for different AFRs in a compression-expansion machine (CEM). The performance of the spark plug sensor was compared with a Cassegrain reflector using an intensified charge-coupled device. The results showed good agreement with measurements obtained using the Cassegrain reflector. The spark plug sensor was shown to be useful for measuring chemiluminescence of turbulent premixed flames in an SI engine.

In order to reduce the exhaust emission and the fuel consumption in a spark ignition engine, the combustion diagnostics had been developed. However, there are few sensors which can detect the combustion quality for the individual cycle and cylinder in production engines. In previous study, the new technique using a gasket ion sensor for measuring the combustion quality has been proposed. In present study, the flame propagation pattern in a spark ignition engine was detected by using a gasket ion sensor with a circular electrode. The waveforms of ion current obtained from a circular ion sensor were compared with the flame propagation pattern obtained from multiple ion sensors. When the mixture was ignited in offset center of the cylinder, the flame propagation pattern was distorted from the spherical pattern. Then the waveforms of ion current from the circular ion sensor were varied from the waveform for a center ignition.

An investigation was made into two approaches to air-fuel mixture formation in direct injection SI engines in which charge stratification is controlled by swirl or tumble gas motions, respectively. Particle image velocimetry (PIV), laser-induced fluorescence (LIF) and air-fuel ratio measurement by infrared absorption were used to analyze fuel transport from the fuel injector to the spark plug and the fuel vaporization process. The results obtained were then compared with measured data as to combustion stability. As a result, the reason why the effects of injection timing on combustion stability were different between the two approaches was made clear from the standpoint of the mixture formation process.

Recently, in order to warm up the catalyst temperature rapidly, the retard ignition management has been developed. However, the excess retard of ignition causes the combustion instability and misfire. In this case, the ion sensor has been used for detecting the combustion quality for the late burned cycle under the idling condition. Several researchers have focused on the potential of ion-current measurement for the retard ignition management. However, the interpretation of ion-current during the exhaust process under the idling condition is not clear. In this study the source of ion-current for the late burned cycle during the exhaust process is focused. In order to measure the flame propagation process in the cylinder and the exhaust pipe, the single-cylinder test engine was used instead of production engine. Several ion probes were mounted on the cylinder head gasket, the piston head and the exhaust pipe for detecting the flame front.

A turbulent entrainment model is considered to be reasonable for the combustion in a spark-ignition engine. For this kind of model, it is important to estimate the turbulence characteristics, turbulent burning velocity, flame surface area and several empirical constants. Nevertheless, the examination of these values have not been examined sufficiently. In this study, a combustion model was proposed, and initiation of flame propagation, burning process of an eddy, scale of turbulence and turbulent burning velocity were discussed in detail. This model was examined under various conditions of engine speed (600-1200rpm), compression ratio (3.2-4.8) and ignition timing. The calculation results of mass fraction burned, burn rate and burn duration were in good agreement with the experimental ones. It was found that the concept of such a turbulent entrainment model was valid for predicting the combustion in a spark-ignition engine.

The structures of the turbulent premixed flame in the engine cylinder under lean burn conditions were investigated using ion probe method. The flow fields were measured with an LDA for two tumble ratios and two compression ratios. And ion-current signal was analyzed to discuss the interaction between the turbulence and the flame structure. The effects of turbulence and equivalence ratio on the characteristic values of the turbulent flame, that is to say number of ion-current peaks, thickness of flame front and thickness of burning zone of the flamelet, were investigated. In normal combustion, the structure of the turbulent flame front is almost the same as the laminar flame. In the lean limit, the flamelet is broken and stretched and then the structure may change.

Bio-gas as an internal combustion (I.C.) engine fuel has many advantages such as cheaper fuel cost, low emission levels and especially the neutral recirculation loop of carbon dioxide, which is one of the principal factors in global warming. In this study, positive potentialities of bio-gas were investigated using a micro co-generation engine. The mixing ratio of methane (CH4) and carbon dioxide (CO2) was changed to simulate various types of bio-gases. Intake air and fuel flow rates were controlled to change the equivalence ratio. The engine load condition could be changed with the electric output power used. Base on the result, the higher CO2 content rate slowed down the engine speed in the same load condition and the combustion speed generally decreased under the same load condition with maintaining the engine speed. However thermal efficiency increased with lean burn conditions and NOX emission decreased with higher CO2 mixing rates.

In this research, a spark plug with an optical fiber has been developed to obtain the emission spectra from the spark discharge and flame kernel. This developed spark plug with an optical fiber can obtain the time series of emission spectra from the spark discharge and Initial flame kernel in the real spark-ignition engine using EMCCD spectrometer. The plasma vibrational temperature of the spark discharge can be measured using the emission spectra from the electrically excited CN violet band system. The plasma of the spark discharge and gas rotational temperature of the initial flame kernel can be also measured using emission spectra from OH* radicals (P and R branches). The plasma temperature of the spark discharge was almost 8,000 K and the gas temperature of the Initial flame kernel approached that of the adiabatic flame temperature.

The authors have previously proposed a plume ignition and combustion concept (i.e., PCC combustion), in which a hydrogen fuel is directly injected to the combustion chamber in the latter half of compression stroke and forms a richer mixture plume. By combusting the plume, both cooling losses and NOx formation are reduced. In this study, thermal efficiency was substantially improved and NOx formation was reduced with PCC combustion by optimizing such characteristics as direction and diameter of the jets in combination with combustion of lean mixture. Output power declined due to the lean mixture, however, was recovered by supercharging while keeping NOx emissions at the same level. Thermal efficiency was further improved by slightly re-optimizing the jet conditions.

An in-spark-plug flame sensor was developed to measure local chemiluminescence near the spark gap in a practical spark-ignition (SI) engine in order to study the development of the initial flame kernel, flame front structure, transient phenomena, and the correlation between the initial flame kernel structure and cyclic variation in the flame front structure, which influences engine performance directly. The sensor consists of a commercial instrumented spark plug with small Cassegrain optics and an optical fiber. The small Cassegrain optics were developed to measure the local chemiluminescence intensity profile and temporal history of OH*, CH*, and C2* at the flame front formed in a turbulent premixed flame in an SI engine. A highresolution monochromator with an intensified chargecoupled device (ICCD) and spectroscopy using optical filters and photomultiplier tubes (PMTs) were used to measure the time-series of the three radicals, as well as the in-cylinder pressure.

In order to investigate the relation between ion current and combustion characteristics, the ion current signal from a spark plug as an ion probe, pressure history and flame development were measured in a homogeneous propane-air mixture in closed combustion chambers. The flame propagation was measured by Schlieren photography technique. When negative bias is applied to the central electrode of the spark plug, the ion current flows only due to an early flame kernel existing near the spark plug. When positive bias is applied to the central electrode, the ion current flows from the central electrode to the combustion chamber wall and to the ground electrode. Consequently, the ion current is dominated by the contact area between the flame and the combustion chamber wall. The appearance period of ion-current is related to the combustion duration. This method was applied to the combustion analysis of the spark ignition engine.